Allt Nytt | Kalender | Racerbanor | Arrangörer | Forum | Varvtider/Loggar |
Sparade trådar/FAQ how to, bygg ett engelskt hjul (litet) | 1, 2 >> 11 besök senaste veckan (7579 totalt) |
|
|||||||||||||||||||||||||||||||
tjo, då jag inte kommer göra nåra fler små engelska hjul så tänkte jag visa lite hur mina va gjorda,texten är på engelska då jag postat detta på ett amerikanskt forum innan å orkar inte översätta
posta gärna bilder å text om era egna verktyg hur enkla eller simpla dom än må va ok this is a WERY simple english wheel that i have made a bunch of now,there are no interchangeble dies,instead the dies are standard bearings (SKF) and the frame are standard box tubing,i'm a simple man with simple tools so have some tolerance all measurments are in millimeter (1inch=25,4mm) so you'll have to get your calculators to change the numbers frame base,100X50X3-4mm 1= 490mm cut 45' 1= 530mm cut 45' 1= 400mm 90' both ends weld the 45' bits together to form an L at 90',then weld the 400mm pice on the 530mm at 260mm from underneath the 490mm piece,now you have the base frame cut a piece of 40X40X4 tubing to 250mm, i choose to do the ends in my lathe to make sure they are perfect, ,drill a 5mm hole 80mm from one end to tap 6mm tread and one 12mm hole 30mm from the other end countersink the edge on the 12mm cut a piece of 32X32 solid bar to 170mm, again do the ends on the lathe, as you can see i have rounded the edges of the solid bar,this in tha lathe to make it fit inside the 40X40,drill one end with a 6mm drill 10mm rom the end and 7mm from the edge,after that drill one 18mm hole in the end of the bar,this for the up and down control of the lower die, cut a treaded 20mm bar to 230mm and do one end like shown in the pic,outer diameter 18mm ,match the groove to the 6mm hole in the solid 32X32, from a 90mm long M20 nut cut a a 30mm bit of then drill 3 holes to tread 8mm, cut 3 pieces of 8mm bar and tread both ends to 8mm,10mm and 15mm long, fit a 8mm nut to the 15mm end and a plastic knob to the 10mm,you now have 3 of these, mount them to the 30mm M20 nut to create this,it's the handle for adjusting the lower die drill and tap a 6mm hole in a 90mm M20 nut 40mm from one end match these peices and put them together like this,32X32,treaded bar and M20 nut and slide it in to the 40X40mm make sure to cut a groove in the end of the treaded 20mm bar or else you cant dismantle the unit later on put the pieces togehter and line them up like this and tack weld the 20mm nut make sure you can turn it and it don't bind, remove the treaded bar and weld the nut firmly and grind your welds down (if wanted),i again used the lathe to make this tidy finish to the bit,and here it's assembled again with treded bar and handle, now it's time to make a simple jig fo make sure the upper and lower dies align,and for this i cut a bit of the 40X40 tube to 250mm,drill a 12mm hole 170mm from one end and cut an acces hole on the opposite side to gain acces to the hole from inside, put the adjusting bit inside the jig, cut a piece of 50X10mm flat bar to 100mm and drill and tap a 12mm hole 20mm from the edge bolt it to the jig with the grease nipple holes in the adjuster facing you and align it to the frame base if your happy with the alignment weld the adjuster and the 50X10 piece to the frame and grind down your welds (if needed) now it's time to machine the bits that holds the bearings,one bit 25mmX35mm (widhtXdia) with 2 grooves 3mm from the edge for the locking rings,drill and tap a 6mm hole trouh it and one bit 35mmX50mm (widthXdia) with a 12mm hole,NO grooves for locking rings yet!! cut 2 pieces of 40X5mm 55mm long and drill and countersink a 6mm hole 15mm from one end in booth, mount the lower bearing to the first bit machined and use 2 M6 by 16mm countersunk hexbolt to secure the unit to the 40X5 flat bar pieces,looking like this fit the upper bearing to the 50mm bit and bolt it to the frame in the treaded hole using a M12X40 hex bolt adjust the adjuster so that the lower bearing assembly barely cleares the upper and align it as good as you can, then spot weld the lower bearing mount to the adjuster and remowe the bearings,use a scrap piece cut to 25mm to make sure the lower brackets stay in place,weld solid,and grind to desired finnish,now you can measure the upper bearing for the grooves and machine them desmantle and paint and refit all components it shoul look something like this (maybe better) _________________ janne pettersson |
|||||||||||||||||||||||||||||||
Tack!
Jag har faktiskt lagt till i garageplanen framöver att fixa mig ett engelskt hjul, samt en krymp- och sträckmaskin. Bra how-to! |
|||||||||||||||||||||||||||||||
på bilden på det röda hjulet syns en plåt med den maximala radien utan att göra ränder i plåten, man kan bocka långa typ tröskel profiler genom lite tryck på ena sidan av plåten när man kör igenom rullarna, fråga gärna om jag kan förtydliga lite
_________________ janne pettersson |
|||||||||||||||||||||||||||||||
Jag tror jag har koll på det mesta men för tydlighetens skull frågar jag. När du för in den långa muttern i 40x40-röret, visst fasar du av två kanter? Tycker det ser så ut på bilden. Det är väl 30 mm grepp på muttern. Shimsar du den på de platta sidorna för att den skall ligga mitt i röret eller är det inte så noga?
Guson _________________ Tomas Gunnarsson |
|||||||||||||||||||||||||||||||
En feature som skulle kunna främja uppladdning vore att kunna automatisk konvertera ett inlägg (eller alla ens inlägg i en tråd) till uppladdade bilder, dvs en funktion på servern som laddar ner bilderna från url i img-taggen och sen byter ut sökvägen. Hjälper ju inte när de väl är borta men skulle minska tröskeln för alla som postar på flera forum. Men det kanske är halvt omöjligt att pressa in i forummjukvarans struktur. _________________ Markus Ålind |
|||||||||||||||||||||||||||||||
Det har varit uppe för rätt länge sen och valdes att kunna skylla på användarna för varje enskild bild. Men Magnus har kanske mjuknat i principerna sen dess |
|||||||||||||||||||||||||||||||
Nä Jag vill fortfarande kunna skylla på användarna men nya euregler lägger väl ansvaret på mig ändå numera. Jag ska ju ha automatisk bildanalys som detekterar kopiering av uppeståndsrätt eller vad det heter _________________ Magnus Thomé |
|||||||||||||||||||||||||||||||
Därav att bara komvertera egna inlägg, går ju att ha en att godkännande per bild. Men det är väl mindre sannolikt att någon laddar upp andras bilder om de måste gå omvägeb till sin egen dator. Konverterade min gamla kadetttråd till rejsabilder nyligen efter att ha hittat bilderna i ett mörkt hörn av en hårddisk, men det tog ett gäng timmar att fixa endå, så rätt få lär göra det. _________________ Markus Ålind |
|||||||||||||||||||||||||||||||
Tyvärr är det ju minst sagt jävligt knökigt när det är många bilder och text mellan dom. Där finns det mig veterligen ingen vettig lösning när väl bilderna är försvunna. _________________ Magnus Thomé |
|||||||||||||||||||||||||||||||
Jo, men hade konverting varit enkelt när de bildlänkarna var levande så hade jag fixat det då. Jaja, jag har bara 924-tråden kvar att konvertera manuellt, bilderna till mantan är nog borta för alltid. _________________ Markus Ålind |
|||||||||||||||||||||||||||||||
Sparade trådar/FAQ how to, bygg ett engelskt hjul (litet) | 1, 2 >> 11 besök senaste veckan (7579 totalt) |